Two-Color LSR Breast Pump Flange & Massage Cushion – 2K Overmolding Production Solution
A breast pump flange is a medical-adjacent, skin-contact part that has to do three things at once: hold a stable vacuum seal against the breast, feel soft enough for repeated use without irritation, and survive daily sterilization for the whole life of the pump. That combination forces a two-material design — a rigid body that holds the geometry and connects to the pump, and a soft silicone contact surface that flexes with the skin.
Core Technology Breakdown
Two-Color LSR Injection Molding Machine
Two-material LSR requires independent dosing for each material plus tightly controlled timing between shots, since the bond forms during a narrow cure window.
-
-
▸ Independent injection and dosing units for the rigid first shot and the LSR second shot, with no cross-contamination between materials.
-
▸ Closed-loop servo control holds shot weight consistent across all 4 cavities, which keeps the soft layer’s wall thickness — and therefore the sealing force — identical part to part.
-
▸ Controlled low-pressure LSR injection fills the thin cushion section without deforming or stressing the rigid substrate.
-
▸ Precise inter-shot sequence and dwell control so the second shot is injected exactly when the interface is ready to bond.
-
▸ Independent temperature control per injection unit and per mold half, so LSR vulcanizes fully without overheating the rigid component.
- ▸ Stored, repeatable parameter sets so the validated two-shot sequence is recalled exactly after every changeover.
-
4-Cavity 2K Cold-Runner Mold
The mold in this project runs two cavity pairs per shot position, with the first-shot cavities and second-shot cavities machined into matched plates and indexed between stations.
-
-
-
▸ Cold-runner system with needle-valve cold nozzles.LSR stays uncured in the manifold, so there is no runner scrap, no sprue, and nothing to recycle. Material utilization approaches 100%.
-
▸ Sprueless design. No gate vestige is left on the skin-contact surface or on the sealing rim.
-
▸ Precision shut-off at the material boundary. The line where silicone meets the rigid part is machined tight enough that silicone cannot creep onto the pump-connection geometry or past the designed edge.
-
▸ Flash-free sealing rim. The vacuum seal depends entirely on this edge; flash here causes suction loss, so the parting line is machined and maintained to leave the rim finished straight out of the mold.
- ▸ Accurate substrate location in every cavity, so silicone thickness is uniform around the full circumference and the cushion does not sit thicker on one side.
-
-
Result: One integrated part with a soft, even, skin-contact surface and a sealing rim that needs no trimming.
In-Mold Bonding — No Glue, No Delamination
The cold-runner mold is the heart of the system. Our design features:
-
-
▸ Self-adhesive, food-grade LSR bonds chemically to the 【PP / PC / PA – confirm substrate】 component during vulcanization. No primer, no adhesive, no secondary assembly.
-
▸ The bond forms inside the mold, so there is no glue line to soften, no rim to lift, and no gap for milk residue to enter.
-
▸ Peel testing shows cohesive failure on correctly processed parts — the silicone tears before the interface separates.
-
- ▸ Survives repeated boiling, steam, and dishwasher sterilization without the edge lifting typical of glued or assembled cushions.
-
-
Material & Hygiene Compliance
A dedicated robotic arm enters the open mold and grips all 4 finished brushes
-
-
▸ Platinum-cured, food-grade LSR, leaving no peroxide by-products and no odor or taste transfer to expressed milk.
-
▸ BPA-free, with material grades available to FDA 21 CFR 177.2600, LFGB, EU 10/2011, and USP Class VI depending on your target market and claim set.
-
▸ Non-porous, smooth molded surface that cleans fully and gives bacteria nowhere to lodge — unlike an assembled joint with a seam.
- ▸ Post-curing available when your specification calls for the lowest possible volatile content.
-
-
Key Benefits at a Glance
| Benefit | Detail |
| One-Step Overmolding | Soft silicone is molded and bonded to the rigid part in one cycle. No gluing, no assembly. |
| No Delamination | In-mold chemical bonding survives repeated sterilization with no edge lift. |
| Reliable Suction | Flash-free sealing rim and uniform cushion thickness keep vacuum performance consistent. |
| Hygienic by Design | No glue seam, no gap, no residue trap. |
| Zero-Waste Molding | Cold-runner needle-valve gating: no sprues, no runners, near 100% LSR utilization. |
| 4-Cavity Output | Four finished parts per cycle, sized for mother-and-baby production volumes. |
| Lower Labor Cost | No deflashing, no gate trimming, no cushion assembly step. |
Technical Specifications
| Parameter | Specification |
| Machine Type | TYM W5555 Horizontal LSR Injection Molding Machine |
| Molding Process | Two-shot (2K) LSR injection molding |
| Injection System | Dual servo-driven plunger units, closed-loop control |
|
Mold Cavities |
4 cavities, 2K cold-runner design |
|
Gate Type |
Needle-valve cold nozzles |
|
Gate/Flash Condition |
Sprueless, no flash, no color bleed |
|
Demolding |
Robotic gripper extraction with tray/conveyor placement |
|
Application |
Two-color kitchen scrubber brush / dish washing pad |
One Supplier. One System. One Guarantee.
We deliver the two-color machine, the 4-cavity cold-runner overmolding mold, and the automation as one matched system from a single source — a decisive advantage on 2K projects, where shot timing, substrate location, and mold indexing have to be tuned together rather than negotiated between vendors.
Proven in Production
Our 4-cavity two-color LSR breast pump part solution is already running in production, delivering:
Made for Global Standards
Frequently Asked Questions
Projects
How strong is the bond between the silicone and the rigid part?
Can my existing rigid flange components be used as inserts?
Can this mold produce different flange sizes?
What training and support do you provide?
Ready to Transform Your Nipple Production?
Contact us today for a free consultation, process analysis, and quotation.
We can provide production simulations, sample molding, and ROI projections tailored to your specific requirements.
You May Also Like
The vertical machine will open and close the mold in the vertical direction. The double slide plate can be installed with one upper mold and two lower molds. It can cooperate with the double station operation to improve the production efficiency, and is more suitable for the production of rubber coated products of silica gel package inserts.
Direct pressure mold opening and closing system.It's more suitable for producing the LSR parts which can be automatically removed from the mold.It can be used for the production of silicone products in multiple industries - automotive wiring harnesses, baby pacifiers, menstrual cups, medical valve plugs.
Direct pressure mold opening and closing system.It's more suitable for producing the LSR parts which can be automatically removed from the mold.
There are two injection units, two separate feed systems and color slurry addition systems. A unified system control panel can be used to achieve two different colors or hardness of liquid silicone. Formed in the machine at the same time, Suitable for the production of double color silicone products or double hardness silicone products.
© 2026 TYM. All Rights Reserved.





Facebook
TikTok
TYM Silicone Machinery